DIGITAL CLAMP METER KYORITSU KEW 2003A JAPAN

Manufacturer: TES
Model: TES-3082
Original: Taiwan

True RMS Reading
4000 count Reading
AC/DC 600A
DCA One-touch-Zero
Current: (DC/AC): (+/-1.9%rdg +/-5dgts)
400A/600A
Voltage: (DC/AC) DC-600V; AC-400V/600V
Resistance: (Ohms)4K
Frequency: (Autorange) 4KHz/20KHz

Manufacturer: TES
Model: CM-01
Original: Taiwan

- High Resolution DC/AC 10mA
- 23mm Large Jaw Diameter
- One Touch Zero for DCA adjustment
- Large 3 3/4 Digits LCD (4032 Counts)
- Fast Analog Bargraph Display
- Max/Min, Data Hold
- 600Vrms Overload Protection for Ohm Measurement
- AC/DC Current: 40A/0~150A/150~200A
-AC/DC Voltage: 400V
- Resistance: 40~400 Ω (beep if < 40.0Ω )
- Frequency: 1~100KHz

Manufacturer: TES
Model: CM-03
Original: Taiwan

-10uA Ultra High Resolution on 40mA range
-30mm Large Conductor Diameter
-ACA 5 Range (40mA, 400mA, 4A, 40A, 60A)
-Fast bargraph display (30 times/sec.)
-Max/Min, Data Hold function
-Relative measurement
-AC Current: (+/-1.0% rdg +/-3dgts) 40m/400m/4A/40A/60A
-AC Voltage: 400V
-Resistance and Continuity: 40~400 Ω

Manufacturer: TES
Model: Prova 2003
Original: Taiwan

- DC 2500A, AC 2100A
- ϕ 55mm, Bus Bar 65mmx24mm
- Auto Range A, V, Ω, Hz
- DCA One Touch Zero
- Diode Test
- Continuity with buzzer
- Max/Min/Hold
- Relative Measurement
- Large 3 3/4 Digits LCD
- Fast bargraph display
- Resistance measurement
- Current: (AC/DC)
DC~400A/2500A
AC~400A/2100A
- Current Analog Output: 400A/2,100A(1mV/A)
- Voltage: (AC/DC)
DC~400m/4V/40V/400V/600V
AC~4V/40V/400V/600V
- Frequency: (Hz) 1~100KHz

HVAC Application：

Check current draw in motors and compressors.
Use MAX/MIN/Rescording in the temperature mode to assess efficiency.
Test run/start capacitors.
Confirm low voltage control signals.
Measure flame safeguard device current draw.
Confirm power sources.
Analyze temperature and voltage or current data with the aid of the time stamp.
Insulation test up to 100M Ω.

Electrical Application：

Check for energized circuits and balance loads.
1 Φ /3 Φ (3P3W/3P4W)Power analyzer.
Evaluate electrical contacts.
Capture motor in-rush current readings.
Determine peak power demand periods.
Verify line voltage stability.
Monitor motors and other loads for excess heat.
Check motor run/start capacitor values.

Manufacturer: TES
Model: TES-3082
Original: Taiwan

True RMS Reading
4000 count Reading
AC/DC 600A
DCA One-touch-Zero
Current: (DC/AC): (+/-1.9%rdg +/-5dgts)
400A/600A
Voltage: (DC/AC) DC-600V; AC-400V/600V
Resistance: (Ohms)4K
Frequency: (Autorange) 4KHz/20KHz

Manufacturer: TES
Model: TES-3050
Original: Taiwan

- 3-3/4 Digital LCD with bar-graph
- Auto-power off with Data Hold & MAX/MIN mode
- Zero Adjustment/Relative Reading
- Current: (AC) 400/1,000A
- Voltage: (AC/DC)
DC-400mV/4V/40V/400V/600V
AC-4V/40V/400V/600V
- Resistance: (Ohm) 400Ω/4KΩ/40KΩ/400KΩ/4MΩ/40MΩ

- Frequency: (Hz) 100Hz/1KHz/10KHz/100KHz/ 800KHz

Manufacturer: TES
Model: TES-3010
Original: Taiwan

- Frequency Count, Diode Check & Beeper
- Peak/Data Hold
- Unit & Sign Display
- Current: (AC)
20/200/600A (TES-3010)
- Voltage: (AC/DC) DC-1,000V; AC-200V/750V
- Frequency: (Hz) 2KHz
- Ohms: (Resistance) 200 Ω /20K

Manufacturer: TES
Model: TES-3012
Original: Taiwan

- Frequency Count, Diode Check & Beeper
- Peak/Data Hold
- Unit & Sign Display
- Current: (AC) 20/200/600/1,000A
- Voltage: (AC/DC) DC-1,000V; AC-200V/750V
- Frequency: (Hz) 2KHz
- Ohms: (Resistance) 200 Ω /20K

3-1/2 Digital LCD, 2000 count.
Pocket size.
MAX hold / Data hold function

Manufacturer: TES
Model: TES-3092
Original: Taiwan

-Compact & Pocket Size
-AC 700A & DC 800A
-600V AC & 200V DC Ohm/Continuity Beeper.
-One Touch DAC Zero
-DC/AC Current:
200A/800A (DCA)
200A/700A (ACA)
-DC/AC Voltage:
200V (DCV)
600V (ACV)
-Ohms: 2K

-Resolution: 0.1 A/1A, 0.1V/1V

Manufacturer: TES
Model: TES-3063
Original: Taiwan

-True Power/Apparent/Power Factor
-RS-232 interface to talk with PC
-Dual display KW+PF, KVA+PF, V+A, A+Hz, V+Hz
-Datalogging Capacity (4000 Reading)
-Peak/Max/MIN function
-True Power & Apparent Power
-Measurement: V<130V, A<150A/V>130V, A<150A/V<130V, A>150A/V > 130V, A>150A
-DCA/ACA/DCV/ACV: DCA & ACA-1000A; DCV & ACV-600V
-Peak Indication: 20~80A, 80~1000A; 20~80V, 80~600V
-Resistance: 10K
-Frequency (Hz): 1KHz/5KHz

Manufacturer: TES
Model: TES-3092
Original: Taiwan

- Non-Contact Ground Resistance Measurement
- No Auxiliary Electrode Needed
- Jaw Diameter 23mm
- 0.2mA~30A True RMS
- 116 Sets of Memory
- Programmable High and Low Alarm
- Programmable Data Logging
- Data Logging interval:1 to 255 sec
- Ground Resistance:
- 0.025~0.250/0.251~1.000/ 1.001~10.00/10.01~50.00/ 50.01~100.0/100.1~200.0/ 200.1~400.0/400.1~600.0/ 600.1~1500

- Ground/Leakage Current: (50/60Hz, True RMS ) 0.300~1.000/1.00~10.00/ 10.0~100.0/100~1000mA/ 0.20~4.000A/ 4.00~30.00A

Manufacturer: TES
Model: TES-3040
Original: Taiwan

- 3-3/4 Digital LCD with bar-graph
- Auto-power off with Data Hold & MAX/MIN mode
- Zero Adjustment/Relative Reading
- Current: (AC) 400/1,000A
- Voltage: (AC/DC)
DC-400mV/4V/40V/400V/600V
AC-4V/40V/400V/600V
- Resistance: (Ohm) 400Ω/4KΩ/40KΩ/400KΩ/4MΩ/40MΩ
- Frequency: (Hz) 100Hz/1KHz/10KHz/100KHz/ 800KHz

Manufacturer: TES
Model: TES-3910
Original: Taiwan

- Inrush Current measurement
- Check 3Φ phase sequence
- Variable-frequency drive (VFD) V &Hz measurement.
- Lo-Z voltage measurement to drain ghost voltages.
- A measurement for HVAC flame sensors.
- mV measurement range to interface with other accessories.
- Crest Factor & Harmonic ratio measurement
- True RMS reading on AC and DC+AC mode
- Data Hold, Auto hold & Peak hold mode
- Max / Min record mode
- Data memory & read function (10 readings)
- AC Current (40Hz to 400Hz) VFD Trms :
+ Range /Resolution/ Sensitivity:
99.99A/ 10mA />0.25A
999.9A /100mA />2.5A
+ Accuracy: +/-2% +/- 20dgts (50, 60Hz); +/- 4% +/- 20dgts (40 to 400Hz)
+ Overload Protection
: 1000A

Manufacturer: TES
Model: TES-3900
Original: Taiwan

- Motor Inrush Current measurement
- Check 3Φ phase sequence
- Variable-frequency drive (VFD) V &Hz measurement.
- Lo-Z voltage measurement to drain ghost voltages.
- Data Hold, Auto hold & Peak hold mode
- Max / Min record mode
- Data memory & read function (10 readings)
- AC Current (50Hz to 400Hz) :
+ Range /Resolution/ Sensitivity:
99.99A/ 10mA /0.10A
999.9A /100mA /1.0A
+ Accuracy: +/-2% +/- 20dgts (50, 60Hz); +/- 4% +/- 20dgts (40 to 400Hz)
- ACA Inrush Current :
+ Range/ Resolution/ Sensitivity
99.99A/ 0.01A/ >5A
999.9A/ 0.1A />50A
+ Measurement Time: 100mS
- AC Voltage (50Hz to 400Hz) :
Range /Resolution/ Accuracy/ Sensitivity
999.9mV/ 0.1mV/[+/- 1% +/- 20 dgts (50, 60Hz)]/ 2.0mV
9.999V /1mV /[+/- 1% +/- 20 dgts (50, 60Hz)]/ 0.020V
99.99V /10mV/ [+/- 2% +/- 20 dgts (40 to 400Hz)]/ 0.20V
600.0V/ 100mV/[+/- 2% +/- 20 dgts (40 to 400Hz)]/ 2V

• Fully Safety jaw
• Ergonomic over-molded body gives convenient one-hand operation
• Large easy-to-read display with 0.1A resolution
• Accurate reading with True RMS
　600/1000A auto-ranging
• Long battery life
• Safety Standard
　 IEC 61010-1 CAT IV 300V / CAT III 600V

• Designed to meet international safety standard IEC 61010-1 CAT IV 600V.
• CAT IV Clamp Meters can measure the Voltage and Current in both every low and high power circuits.
• Very useful for power distribution companies, power utilities and maintenance fields.

• DC voltage range is also available especially for checking emergency battery operated power supply.
• Tear drop shaped transformer jaws for ease of use.

• Designed to meet international safety standard IEC 61010-1 CAT IV 600V.
• CAT IV Clamp Meters can measure the Voltage and Current in both every low and high power circuits.
• Very useful for power distribution companies, power utilities and maintenance fields.
• True RMS enables an accurate measurement

• Small and handy clamp meter
• IEC 61010-1 Safety Standard CAT Ⅲ 300V, CAT Ⅱ 600V
• 400A AC/DC Clamp meter
• DMM function ACV, DCV, Ω, Continuity Buzzer

• Small and handy clamp meter
• IEC 61010-1 Safety Standard CAT Ⅲ 300V, CAT Ⅱ 600V
• 400A AC Clamp meter
• DMM function ACV, DCV, Ω, Continuity Buzzer.

• Designed to meet international safety standard IEC 61010-1 CAT IV 600V.
• CAT IV Clamp Meters can measure the Voltage and Current in both every low and high power circuits.
• Very useful for power distribution companies, power utilities and maintenance fields.
• True RMS enables an accurate measurement.

• Measures 4 to 20 mA instrumentation and process signals without breaking the loop
• Memory function stores up to 192000 data useful for monitoring the signals over time and fault finding
• Transfer data to PC via Bluetooth
• Top class measurement 0.2% accuracy
• ∅6mm clamp jaw easy to use in tight places
• LED light for illuminating the measurement spot
• Analog output terminal to allow the connection to a recorder or a digital multimeter

Extremely large jaw with tear drop shape:
ideal solution for busbar and large currents!

・Conductor size φ75mm and busbar of 80×30mm or less
・Current up to 1000A rms
・Voltage up to 1000V rms
・Harmonics up to 30th
・Various measurement functions: current, voltage, power, harmonics
   and phase detection
・LCD can display simultaneously the values of voltage and frequency
   or power and power factor
・Each degree of harmonics can be shown on the LCD of the tester
・BluetoothⓇ communication functions

Ø110mm

• Can measure AC current up to 1000A
• Flexible and light weight by the air core coil used at the sensor part
• Designed to meet the international safety standard IEC 61010-1 CAT IV 300V, CAT III 600V